How To Change Fuel Filter On John Deere Tractor: Maintenance Guide

John Deere Tractors are known for their durability and dependability. They have been around since the early 1900s and have become one of North America's most popular brands of tractors.

If you own a John Deere tractor, you know it can last a long time if properly maintained. However, there are some things you need to keep in mind when changing the oil and filters on your John Deere tractor.

Changing a fuel filter on your tractor is integral to keeping it in good working order. The fuel filter should be changed every year or two, depending on how often you use the tractor and what kind of work you do with it.

Read on to know more.

John Deere Tractor Oil Filter Replacement Procedure

ALT TEXT: A John Deere tractor

Step 1: Remove the cover plate

Remove the cover plate from the bottom of the engine compartment. Be careful not to drop parts inside the engine compartment, as this could cause damage to other components.

Step 2: Remove the drain plug

Use a screwdriver to remove the drain plug under the engine hood. Removing the drain plug will allow you to drain out all the old oil before replacing the new filter.

Step 3: Disconnect the fuel line

Disconnect the fuel line connector from the fuel tank. This allows for easy removal of the old filter and installation of the new one.

Step 4: Drain the oil out of the filter housing

Turn the engine over until the oil drains out of the filter housing. Doing this ensures that no old oil remains in the filter housing.

Step 5: Replace the drain plug.

The next step is to replace the drain plug on the engine block. This ensures that the engine has enough space to drain all the oil.

Step 6: Check your oil level

Check the oil level inside the engine compartment to ensure it is low. If it is too high, then add oil using the dipstick. Also, check the oil level in the radiator. Repeat Steps 1 through 6 to replace the oil filter.

Step 7: Install the new filter

Install the new filter by turning the engine over until the new filter is seated correctly. Depending on the model of your tractor, you may have to push down the filter while installing it. Once installed, tighten the bolts to secure the filter in place.

Step 8: Reconnect the fuel line

Connect the fuel line connector back onto the fuel tank. This step ensures that the tractor runs smoothly after the replacement process.

Common Issues You Might Face

Even though changing the oil and filters is simple, you might still need help with certain issues. The following are some common issues that may occur while using your tractor.

Lube pump failure

Problems may arise when the lube pump fails because the tractor will start leaking oil. If the lube pump fails, the tractor will lose power. The tractor will be unable to move forward or backward.

If this happens, turn off the ignition switch and wait for the tractor to cool down before attempting to restart the tractor. When the tractor starts running normally, try starting the lube pump manually.

Lube pressure loss

If the lube pressure drops below a certain point, the tractor will not start. This can lead to severe problems such as overheating and even fire.

To fix this issue, turn off the ignition switch and let the tractor cool down before trying to restart the tractor. If the problem persists, contact a mechanic and ask them to help you repair it.

Lube leak

If there is a leak in the lube circuit, the tractor will have trouble starting. This is because the water in the lube circuit could cause corrosion.

To prevent this problem, keep the lube system clean at all times. Turn off the ignition and allow the tractor to cool down before cleaning. Also, do not use sharp objects near the lube circuit. Contact a mechanic if the issue continues.

Lube pump overheating

Overheating the lube pump can cause damage to the pump itself. The excess heat can also cause the lube pump to fail.

To avoid this issue, turn off your tractor and allow it to cool down completely. Once the temperature has dropped, reconnect the battery and try to start the tractor. If the tractor starts successfully, the lube pump is probably damaged during the overheating event.

Checking John Deere Engine Oil Level Manually

If your John Deere tractor does not have an oil level sensor, you will need to check the oil level manually. Follow these steps to check the oil level yourself.

1. Turn off the ignition switch. This ensures that no electrical current flows through the engine.

2. Open the radiator cap. Allow for air to flow into the radiator.

3. Look at the dipstick. You know the oil level is too high if there is no oil in the dipstick tube. You may need to adjust the height of the oil pan or lower the oil pan.

4. Close the radiator cap to stop airflow into the radiator.

5. Recheck the oil level by looking at the dipstick.

5. Start the engine. If your oil level is low, then you should add more oil.

6. After the engine has started, look at the dipstick again and make sure that the oil level is correct.

7. Close the radiator cap and turn off the engine. It's important to close the radiator cap after adding oil, so it doesn't spill out of the radiator.

8. Remove the dipstick from the oil pan. This prepares the dipstick for future readings.

9. Fill the oil pan with oil.

10. Reinstall the dipstick into the oil pan.

11. Turn the ignition switch on.

12. Wait for the engine to warm up.

13. Check the oil level once more. If the oil level is correct, then you know that your oil level sensor works.

Frequently Asked Questions:

What are some common problems with tractors?

Here are some common problems with John Deere tractors:

• The tractor won't start - The most common reason a tractor won't start is that the spark plug wire isn't connected properly. Make sure that the spark plug wires are connected correctly.

• The tractor won't stop running - This problem usually occurs when the ground strap is loose. Tighten the ground strap by pulling it toward the tractor.

• The tractor won't shift gears - Pull the clutch lever all the way forward to ensure the transmission is working correctly. This will disengage the clutch. Then, push the clutch lever all the way from you. This will engage the clutch.

• The tractor doesn't move after starting - The steering wheel may be stuck in one position. Pull the steering wheel back until it moves freely.

Learn More About John Deere Fuel Filters at Heavy Duty Pros

Overall, fuel filters for John Deere tractors are relatively easy to change and install. Just keep in mind that changing them requires a bit of patience. Also, be careful not to overfill the tank with oil. Overfilling the tank could cause the engine to stall.

If you want to know more about a fuel filter on a John Deere tractor, check out our website. Our resources at Heavy Duty Pros have lots of helpful information about quality truck fuel filters and more.